THE GP RANGE OF ROLLBARS WILL FIT YOUR MAZDA MX5

MK1 MK2 MK2.5 WITH GLASS OR PLASTIC REAR WINDOW

AND YOU CAN ALSO FIT YOUR HARD TOP

********************************************************

• Hand made from quality high grade carbon steel
• Offers greatly improved occupant safety in the event of the vehicle rolling over
• Designed specifically for use with all soft tops including glass and plastic back windows
• Suitable for use with hard tops
• Allows full seat back movement
• Prove to add chassis rigidity giving improved handling
• Finished in a high quality and durable black powder coated finish
• Supplied with all the required fittings and instructions

Fits all right and left hand drive Mk1, Mk2 & 2.5 models, 1989>2005

Please note: This is not suitable for use with any other style bar or wind blocker except the Mk2/2.5 factory wind blocker (minor modifications will be required).

Some Mazda mx5 seats may not be compatible with our rollbars so please contact us first for if you need any further info

Disclaimer: TR Lane NOT will be responsible or held liable for any damage, loss or injury sustained whilst fitting or using this product

ROLL BAR FITTING INSTRUCTIONS

1. MOVE BOTH SEATS FORWARD, TILTED FORWARD, GIVING ACCESS

TO REAR AREA. POSITION HOOD IN DOWN POSITION. REMOVE

SEAT BELT SHOULDER STRAPS FROM TOP OF SEAT BELT TOWERS.

REMOVE PLASTIC COWLING SURROUNDING SEAT BELT TOWERS,

GIVING ACCESS TO SEAT BELT REELS. REMOVE YOUR PARCEL

SHELF CARPET AND FIRE WALL CARPET. REMOVE PARCEL SHELF

TRAY, TAKING GREAT CARE AS THIS ITEM CAN BE VERY SHARP.

THIS WILL GIVE YOU ACCESS TO WHERE THE ROLL BAR NEEDS TO

SIT.

2. JACK UP CAR, SECURELY UPON AXLE STANDS. REMOVE REAR

WHEELS. REMOVE SPLASH TRAYS WHICH ARE LOCATED IN FRONT

OF THE REAR WHEELS, IN FRONT OF THE ARCHES. WHERE ROLL BAR

SITS IN CAR, YOU WILL NEED TO LOOSEN ALL FIXINGS WHICH

HOLD WIRING HARNESSES IN POSITION. THERE ARE ALSO THREE

SMALL BOLTS ON EACH SIDE OF THE SEAT BELT TOWERS BY YOUR

WIRING HARNESSES - THESE NEED TO BE REMOVED. THE TWO

ANGLE BRACKETS WHICH THE REAR PARCEL SHELF MOUNTS TO,

YOU WILL NEED TO REMOVE 4" OF THIS EACH SIDE, ENABLING YOUR

ROLL BAR TO SIT NEATLY BETWEEN SEAT BELT TOWERS.

3. PROCEED TO FIT ROLL BAR IN POSITION, USING YOUR SEAT BELT

TOWER BOLTS, LOCATE THE ROLL BAR SIDE MOUNTING PLATES,

YOU MAY NEED TO MAKE SOME SPACERS OR YOU CAN USE

EXISTING TOP HAT SPACERS THAT HAVE COME OFF YOUR

SHOULDER STRAP BOLTS. PROCEED TO LIGHTLY TIGHTEN THESE

BOLTS, ENSURING THAT THE ROLL BAR FEET PLATES ARE SITTING

ON THE CHASSIS AREA. ADJUST YOUR ROLL BAR SO THAT THE

FEET PLATES SPREAD OUT NEATLY BETWEEN THE SEAT BELT

TOWER SIDES (THERE MAY BE A GAP IF A HARNESS BAR IS

PROVIDED DUE TO WELDING HEAT DISTORTION) BUT THIS CAN

BE OVERCOME BY BOLTING TO THE SIDES OF PILLARS.

4. WITH A CENTRE PUNCH, PUNCH DOWN THROUGH THE HOLES AS

HARD AS YOU CAN, THEN YOU WILL FEEL UNDER THE CAR WHERE

YOU HAVE PUNCHED DOWN THROUGH, PUNCH BACK UP THROUGH

FROM UNDERNEATH, THEN WITH A PILOT DRILL, DRILL UP THROUGH

AND THEN DRILL AGAIN WITH APPROPRIATE DRILL. BOLTS DOWN

THROUGH, THERE ARE BACKING PLATES TO BE ATTACHED ON

REAR STAYS WHICH CAN NOW BE TIGHTENED IN POSITION.

5. REMOVE SEAT BELT REELS, YOU MAY PROCEED TO DRILL THROUGH

THE SIDE MOUNTING PLATES AND THEN PROCEED TO NUT AND

BOLT TOGETHER, AND THEN RE-ATTACH SEAT BELT REELS.

(AS A SAFETY MEASURE, GET A SECOND PERSON TO CHECK THAT

YOU HAVE TIGHTENED THE SEAT BELT REELS). FINALLY CHECK

THAT YOU HAVE TIGHTENED ALL THE NUTS AND BOLTS. WHEN

YOU ARE HAPPY WITH INSTALLATION, YOU MAY PROCEED TO

REPLACE SPLASH TRAYS, FIX WHEELS, SET BACK DOWN ON THE

FLOOR.

6. YOU WILL NOW NEED TO TRIM YOUR REAR PARCEL SHELF AREA.

THIS IS UP TO THE INDIVIDUAL HOW THEY WISH TO DO THIS.

ONCE YOU HAVE FITTED THE PARCEL SHELF, YOU WILL THEN

NEED TO TRIM THE BOTTOM EDGES OF THE SEAT BELT COWLINGS,

ENABLING THEM TO SLIP FROM THE COCKPIT AREA BACK TOWARDS

THE BACK OF THE CAR, SLIDING BETWEEN THE ROLL BAR AND

SEAT BELT TOWERS. THIS CAN SOMETIMES BE A TIGHT FIT AND

MAY NEED SOME GENTLE PERSUASION AND EASING. THEN

PROCEED TO FIT PARCEL SHELF CARPET AND TRIM AS DESIRED.

T.R. Lane Fabrications or any employee of T.R. Lane Fabrications are not in anyway responsible or liable for loss or injury to any persons whilst fitting or using this roll bar.

This is part of the sale agreement. 

• Hand made from quality high grade carbon steel
• Offers greatly improved occupant safety in the event of the vehicle rolling over
• Designed specifically for use with all soft tops including glass and plastic back windows
• Suitable for use with hard tops
• Allows full seat back movement
• Prove to add chassis rigidity giving improved handling
• Finished in a high quality and durable black powder coated finish
• Supplied with all the required fittings and instructions

Fits all right and left hand drive Mk1, Mk2 & 2.5 models, 1989>2005

Please note: This is not suitable for use with any other style bar or wind blocker except the Mk2/2.5 factory wind blocker (minor modifications will be required).

Some Mazda mx5 seats may not be compatible with our rollbars so please contact us first for if you need any further info

Disclaimer: TR Lane NOT will be responsible or held liable for any damage, loss or injury sustained whilst fitting or using this product